TM - GLAP logo - Click takes you to Front Page

''Aircraft Windshields'' - Click here to go to Main Catalog

Order your parts onlineGo to: Catalog IndexGo to: Instructions pageWhat can GLAP do for you and your business?Go to: Cross ReferenceSolutions

888-826-2043

Order your parts online E-mail us with your questions

Home > Catalog >.

Installation Instructions >.
Beech Index >  

Instructions A2C - STC'd 2223 Door Window
INSTRUCTIONS - A2C
Instructions for Installing a Beech Door window with Milled edge and Vent window

Use with GLAP Part # 2223

 

PAGE INDEX:
Usability
Materials required
Installation procedure:
Weight and Balance information
---------------------------------------------
Other Pages
Go to: Beech 33 Index
Go to: Beech 35 Index
Go to: Beech 36 Index
Go to: Beech 55 Index

Go to: Beech 56 Index
Go to: Beech 58 Index
Go to: Beech 95 Index

Usability of Right Hand ( Door ) window
W- or W/T-, W/G-2223
Model  Serial Number
F33A CE-633 & on
V35B D-9819, D-9856 & up 
A36 E-754, E-831 & up 
A36TC EA-1 & up
95-B55 & 95-B55A TC-1936 & up
E55 & E55A TE-1070 & up
58 & 58A TH-733 & up
 
Materials required:
  1. Door Window, W or W/T-, or W/G-2223, STC # SA00690CH
  2. RTV Silicone Rubber Sealant GE, Dow or equal
  3. Optional - VM&P Naphtha or Lighter Fluid
  4. Rivets - as required
 
Installation procedure:
  1. Remove upholster and trim pieces as required, to expose the window retainer.
  2. Drill out the rivets that hold the retaining ring.
  3. Remove old window and clean opening of old sealant.  Inspect opening for distorted metal or damaged surface where new window will contact.
  4. Peal the protective paper back on the new window not more than 1 to 2 inches from edge and use masking tape to hold it.
  5. Place new window in opening and mark any spots that to be sanded for a better fit.  DO NOT REMOVE EXCESSIVE AMOUNTS OF MATERIAL AT ONE TIME - YOU CAN ALWAYS TAKE MORE OFF - YOU CANNOT PUT ANY BACK ON!
  6. Make sure the edges of the window are smooth and then replace the window in the opening.  If any interference still exists repeat step 5.
  7. If the retainer ring overlaps the milled edge of the window or is too tight in a spot or two the inside edge of the metal ring may be trimmed to allow a better fit.
  8. When a good fit is obtained, reinstall the window in the door, and re-rivet the retainer ring holding the window.  NOTE- If the window is masked to the metal edge of the window opening the mess created by the sealant will be minimized.
  9. Remove the masking tape and protective paper when the sealant has dried.
  10. Replace the upholstery and trim pieces removed in step 1.
 
Weight and Balance information

 

    Right hand ( door ) window replace 36-430044-5 with W, W/T, W/G-2223

      New weight change.................................. + 2.7# ( exchange )
      Arm.......................................................... + 88½"
      Moment..................................................... + 170 in #


    Right hand ( door ) window replace 36-430044-3 with W, W/T, W/G-2223

    (Baron Models with .250" window)

      New weight change.................................. + 0.0# ( exchange )
      Arm.......................................................... + 88½"
      Moment..................................................... + 0 in #

 
 
 

888-826-2043

Order your parts online E-mail us with your questions

Home > Catalog >.

Installation Instructions >.
Beech Index >  

A2C STC'd 2223 Door Window